Infiniti FX35, FX50 (S51). Manual - part 118

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  116  117  118  119   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 118

 

 

AV

INSPECTION AND ADJUSTMENT

AV-245

< BASIC INSPECTION >

[NAVIGATION (SINGLE MONITOR)]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

NOTE:
AVM: Around view monitor

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Description

INFOID:0000000005527063

Adjust the center position of the predictive course line of the rear view monitor if it is shifted.

PREDICTIVE COURSE LINE CENTER POSITION ADJUSTMENT : Work Procedure

INFOID:0000000005527064

1.

DRIVING

Drive the vehicle straight ahead 100 m (328.1 ft) or more at a speed of 30 km/h (18.6 MPH) or more.

>> END

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR)

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Description

INFOID:0000000005475095

• Perform the calibration and perform the writing to the around view monitor control unit when removing and

replacing each camera, removing the camera mounting parts (front grille, door mirror, etc.) and replacing the
around view monitor control unit. 

• Align the white lines on the road near the vehicle at the boundary of each camera image by this camera cal-

ibration. The white lines far from the vehicle may not be aligned at the boundary of each camera image. The
farther the line, the greater the difference is. 

CALIBRATING CAMERA IMAGE (AROUND VIEW MONITOR) : Work Procedure

INFOID:0000000005475096

Calibration flowchart

Following the flowchart shown in the figure, perform the calibration. 

NOTE:

JPNIA1341GB

AV-246

< BASIC INSPECTION >

[NAVIGATION (SINGLE MONITOR)]

INSPECTION AND ADJUSTMENT

In the un-match display, the un-match camera position is indicated
as “

” on the birds-eye view. 

Calibration procedure

1.

AROUND VIEW MONITOR SCREEN CONFIRMATION

Check that there is the un-match display in any camera. 
Is the un-match display visible?

YES

>> GO TO 2.

NO

>> GO TO 4.

2.

CHECK THAT AROUND VIEW MONITOR CONTROL UNIT IS REPLACED

Check that the around view monitor control unit is replaced.
Is the around view monitor control unit replaced?

YES

>> GO TO 3.

NO

>> GO TO 5.

3.

RELEASE UN-MATCH DISPLAY (PERFORM ONLY WHEN THE AROUND VIEW MONITOR CONTROL

UNIT IS REPLACED)

1.

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Calibrating Camera Image”
mode. 

2.

Press the “ENTER” switch of the multifunction switch on each
screen of “Rear Camera”, “Front Camera”, “Dr-Side Camera”,
“Pass-Side Camera”. 

CAUTION:

• Do never operate the center dial and up/down/left/right

switches. Only press the “ENTER” switch. 

• Never perform “Initialize Camera Image Calibration”. 

3.

Display the around view monitor screen, and check that there is
no malfunction such as a difference between each camera
image. 

Is there a malfunction?

YES

>> Calibration end

NO

>> GO TO 1.

4.

PERFORM SIMPLIFIED CONFIRMATION/ADJUSTMENT BY “FINE TUNING OF BIRDS-EYE VIEW”

1.

Put target line 1 on the ground beside each axle using packing tape, etc. 

2.

Put target lines 2 equal to the vehicle total length + approximately 1.0 m (39.3 in) from the vehicle side
(right and left) at approximately 30 cm (11.8 in) away from the vehicle (make the line as parallel with the
vehicle as possible) 

JSNIA2378ZZ

JSNIA2378ZZ

JSNIA2379ZZ

AV

INSPECTION AND ADJUSTMENT

AV-247

< BASIC INSPECTION >

[NAVIGATION (SINGLE MONITOR)]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Preparation of simplified target line

3.

Select “Camera Cont.” of Confirmation/ Adjustment mode, and then set to “Fine Tuning of Birds-Eye View”
mode.

4.

Select left and right cameras by pressing the “CAMERA” switch, and perform the following confirmation. 

-

Check that target line 1 is aligned with the marker on the screen. Overlap the line aligned to the marker
with the upper/lower switches if necessary. 

-

Check if there is a difference between target lines 2 between cameras. Adjust target lines 2 to be straight
lines by operating the center dial and left/right switches if necessary. 

CAUTION:

Never adjust the front camera and rear camera. Only adjust the right and left cameras. 

Operate the center dial slowly because the changing of the screen takes approximately 1 sec-
ond. 

Simplified target line adjustment method

5.

Adjust left and right cameras. Check that the difference between target line 1 and the marker on the
screen, and between target lines 2 is solved. 
NOTE:
• It can be initialized to the NISSAN factory default condition with “Initialize Camera Image Calibration” of

“Calibrating Camera Image”. 

JSNIA0927ZZ

1.

Target lines 1

2.

Target lines 2

A.

Approx. 30 cm (11.8 in)

B.

Approx. 1.0 m (39.3 in)

JSNIA0929ZZ

1.

Target lines 1

2.

Target lines 2

3.

Marker for target line 1

4.

Boundary between cameras

5.

Crosshairs cursor (mark indicated 
the selected camera)

A.

Adjustment method for target lines 1 
(right)

B.

Adjustment method for target lines 2 
(right)

AV-248

< BASIC INSPECTION >

[NAVIGATION (SINGLE MONITOR)]

INSPECTION AND ADJUSTMENT

• The adjustment value is cancelled on this mode by performing “Initialize Camera Image Calibration”. 

Is the difference corrected?

YES

>> Finish the writing to around view monitor control unit by pressing “ENTER” switch. 

NO

>> GO TO 5.

5.

PERFORM “CALIBRATING CAMERA IMAGE”

Preparation of target line
1.

Hang a string with a weight as shown in the figure. Put the points FM0, RM0 (mark) on the ground at the
center of the vehicle front end and rear end with white packing tape or a pen. 

2.

Route the vinyl string under the vehicle, and then pull and fix it on the point approximately 1.0 m (39.9 in)
to the front and rear of the vehicle through the points FM0 and RM0 using packing tape. 

Target line preparation procedure 1

3.

Put the points FM and RM (mark) 75 cm (29.5 in) from the points FM0 and RM0 individually. 

4.

Route the vinyl string through the points FM and RM using a triangle scale, and then fix it at approximately
1.5 m (59 in) on both sides with packing tape. 

5.

Put the points FL, FR, RL, and RR (mark) to both right and left [vehicle width / 2 + 30 cm (11.8 in)] from the
points FM and RM. 

Target line preparation procedure 2

JSNIA1054ZZ

1.

Thread

2.

Weight

3.

Point FM0 (mark)

4.

Point RM0 (mark)

5.

Packing tape (to fix the vinyl string)

6.

Vinyl string

JSNIA0921ZZ

1.

Point FM

2.

Point RM

3.

Triangle scale

4.

Point FL (mark)

5.

Point FR (mark)

6.

Point RL (mark)

 

 

 

 

 

 

 

Content   ..  116  117  118  119   ..