Infiniti FX35, FX50 (S51). Manual - part 1068

EXT-22

< REMOVAL AND INSTALLATION >

COWL TOP

COWL TOP

Exploded View

INFOID:0000000005248863

1.

Front fender cover RH

2.

Cowl top cover RH

3.

Battery cover

4.

Hoodledge cover RH

5.

Cowl top cover seal RH

6.

Cowl top cover seal LH

7.

Hoodledge cover LH

8.

Brake master cylinder cover

9.

Cowl top cover RH

10. Front fender cover LH

11. Cowl top seal

12. EPT sealer

: Clip

JMKIA2716ZZ

COWL TOP

EXT-23

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

Removal and Installation

INFOID:0000000005248864

REMOVAL

1.

Fully open hood assembly.

2.

Remove front wiper arms and blades (LH/RH) from vehicle. Refer to 

WW-120, "Removal and Installation"

.

3.

Remove battery cover and brake master cylinder cover.

4.

Remove cowl top cover seals (LH/RH).

5.

Remove hoodledge cover mounting clips and then remove hoodledge covers (LH/RH).

6.

Remove front fender covers (1) fixing clips (LH/RH). 

7.

Remove cowl top seal. 

8.

Remove cowl top covers (LH/RH) fixing clips.

9.

Push pawls (A) and (B) to remove cowl top cover RH (1) as
shown in the figure.

10. Push pawl (A) as shown by the arrow in the figure to remove

cowl top cover LH (1).

INSTALLATION

Note the following itmes, and install in the reverse order of removal.

: Pawl

Refer to 

GI-4, "Components"

 for symbols in the figure.

: Clip

JMKIA2237ZZ

JMKIA2717ZZ

JMKIA2159ZZ

EXT-24

< REMOVAL AND INSTALLATION >

COWL TOP

• Align concave of cowl top cover RH (1) to windshield glass (2) pin

(A) as shown in the figure when installing.

• Slide the pawl while aligning with the concave part of (C).
• Engage the joint of pawl of (A) with (B), and then assemble cowl

top covers LH (1) and RH (2). 

CAUTION:

• Always replace EPT sealer with a new one, if the cowl top cover is reused.
• After installing, perform adjustment of wiper arm. Refer to 

WW-120, "Adjustment"

.

JMKIA2160ZZ

JMKIA2161ZZ

FENDER PROTECTOR

EXT-25

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

FENDER PROTECTOR

FENDER PROTECTOR

FENDER PROTECTOR : Exploded View

INFOID:0000000005248865

FENDER PROTECTOR : Removal and Installation

INFOID:0000000005248866

REMOVAL

1.

Remove front fillet molding. Refer to 

EXT-32, "Removal and Installation"

. 

2.

Remove front fender protectors (front and rear side) fixing grom-
mets (A) with a remover tool (B).

1.

Splash guard (AWD models)

2.

Fender protector (front)

3.

J-nut

4.

Front fender

5.

Grommet

6.

Fender clip

7.

Fender protector (rear)

JMKIA2718ZZ

JMKIA2719ZZ