Infiniti FX35, FX50 (S51). Manual - part 1065

 

  Index      Infiniti     Infiniti FX35, FX50 (S51) - service repair manual 2010 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1063  1064  1065  1066   ..

 

 

Infiniti FX35, FX50 (S51). Manual - part 1065

 

 

EXT-10

< PRECAUTION >

PRECAUTIONS

5.

When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)

6.

Perform self-diagnosis check of all control units using CONSULT-III.

Precaution for Procedure without Cowl Top Cover

INFOID:0000000005248853

When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.

Precaution for Work

INFOID:0000000005248854

• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their

operation.

• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.

PIIB3706J

PREPARATION

EXT-11

< PREPARATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

PREPARATION

PREPARATION

Special Service Tools

INFOID:0000000005248855

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Commercial Service Tools

INFOID:0000000005248856

Tool number

(Kent-Moore No.)

Tool name

Description

(J-39570)
Chassis ear

Locates the noise

(J-43980)
NISSAN Squeak and Rattle 
Kit

Repairing the cause of noise

SIIA0993E

SIIA0994E

Tool name

Description

Engine ear

Locates the noise

Remover tool

Removes clips, pawls and metal clips

Power tool

SIIA0995E

PIIB7923J

PIIB1407E

EXT-12

< REMOVAL AND INSTALLATION >

FRONT BUMPER

REMOVAL AND INSTALLATION

FRONT BUMPER

Exploded View

INFOID:0000000005248857

JMKIA2694ZZ

FRONT BUMPER

EXT-13

< REMOVAL AND INSTALLATION >

C

D

E

F

G

H

I

J

L

M

A

B

EXT

N

O

P

Removal and Installation

INFOID:0000000005248858

REMOVAL

CAUTION:

Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with
oil.

1.

Fully open hood assembly.

2.

Remove front bumper fascia assembly upper side fixing clips
(A).

3.

Remove engine room covers (LH/RH) (For VK engine models). Refer to 

EM-174, "Exploded View"

.

4.

Remove hood seal assemblies (LH/RH) (1) fixing clips (A), and
then remove hood seal assembly located on the front area.
Refer to 

DLK-245, "Removal and Installation"

.

5.

Remove bolts (A) of fixing bumper side stiffener (1) and front
fender (LH/RH).

1.

Bumper side bracket RH

2.

Bumper reinforcement

3.

Energy absorber

4.

Bumper side stiffener RH

5.

Front grille

6.

Front emblem

7.

Front fog lamp finisher RH

8.

Front fog lamp RH 

9.

Bumper fascia assembly lower

10. Front fog lamp finisher LH

11.

Front fog lamp LH

12. License plate bracket

13. Sonar sensor RH

14.

Bumper fascia assembly

15. Sonar sensor LH

16. Bumper side grommet RH

17.

Front camera finisher

18. Bumper side grommet LH

19. Bumper side stiffener LH

20.

Hood top seal

21. Bumper side bracket LH

JMKIA2695ZZ

JMKIA2696ZZ

: Vehicle front

JMKIA2697ZZ

 

 

 

 

 

 

 

Content   ..  1063  1064  1065  1066   ..