Infiniti FX35, FX50 (S51). Manual - part 99

AV

SYSTEM

AV-169

< SYSTEM DESCRIPTION >

[NAVIGATION (SINGLE MONITOR)]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• In the Birds-Eye view, the invisible area is displayed on the image to specify the boundary of the 4 cameras.

The invisible area is displayed in yellow in the Birds-Eye view after turning the ignition switch ON. 

• The sonar (both of buzzer and indicator) operates only when the camera screen is displayed. 

NOTE:
The first, second, and third camera image displayed when switched to the camera image display depends
on the settings of “Camera View Priority”.

Around view monitor screen transition

FRONT VIEW

• The front view image is from the front camera.
• When the selector lever is in any position other than the reverse position, the front view is displayed by

pressing the “CAMERA” switch. It improves the visibility of obstacles in front of the vehicle and helps driving
by the images displayed from Birds-Eye view and Front-Side view. 

• Display the vehicle width guiding line and vehicle distance guiding line in front view and display the predic-

tive course line according to the steering angle.

• If the steering angle is within approximately 90 degrees, the predictive course lines on the left/right side are

displayed. If the steering angle is exceeding approximately 90 degrees, only the predictive course line on the
outside (in the opposite side of steering direction) is displayed.

• AV control unit is connected to the steering angle sensor and receives the steering angle signal via CAN

communication. AV control unit is transmits steering angle signal to around view monitor control unit via AV
communication.

• Around view monitor control unit controls the direction and distance of the predictive course line according to

the sensor signal from steering angle sensor.

JSNIA2381GB

AV-170

< SYSTEM DESCRIPTION >

[NAVIGATION (SINGLE MONITOR)]

SYSTEM

Front view guiding lines

REAR VIEW

• The rear view image is from the rear camera.
• When the selector lever is in the reverse position, the rear view is displayed. Backing and parking are

improved by the images from Birds-Eye view and Front-Side view. The rear wide view function allows the
display of an image with a 180

°

 horizontal angle.

• Display the vehicle width guiding line and vehicle distance guiding line in Rear view and display the predic-

tive course line according to the steering angle (except when using the rear wide view function). 

• The predictive course line is not displayed at the steering neutral position.
• AV control unit is connected to the steering angle sensor and receives the steering angle signal via CAN

communication. AV control unit is transmits steering angle signal to around view monitor control unit via AV
communication.

• Around view monitor control unit controls the direction and distance of predictive course line according to the

sensor signal from steering angle sensor. 

Rear view guiding lines

FRONT-SIDE VIEW

• The front-side view image is from the side camera RH.
• In Front-Side view, display the vehicle distance guiding line and vehicle width guiding line. 
• The infrared LED illumination is installed on the door mirror RH to illuminate around the front wheels. 

JSNIA0770GB

JSNIA2407GB

AV

SYSTEM

AV-171

< SYSTEM DESCRIPTION >

[NAVIGATION (SINGLE MONITOR)]

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

Front-side view area and guiding line

BIRDS-EYE VIEW

• The image from the 4 cameras is cut out and converted into the overhead view, and the surroundings of the

vehicle is displayed in birds-eye view.

• In Birds-Eye view, the invisible area is displayed on the image to specify the boundary of the 4 cameras. 
• The invisible area is displayed in yellow in the Birds-Eye view after turning the ignition switch ON as an infor-

mation for the user. (OFF setting can be performed)

Birds-Eye view display image

JSNIA0771GB

JSNIA1441GB

AV-172

< SYSTEM DESCRIPTION >

[NAVIGATION (SINGLE MONITOR)]

SYSTEM

Birds-Eye view display area

Camera Image Operation Principle

• If the information writing to around view monitor control unit and the information from the camera are not

matched, the applicable camera position is indicated as an error on the Birds-Eye view display. (Calibration
operation is necessary when replacing each camera or when replacing around view monitor control unit.)

• Around view monitor control unit receives the camera switch signal from AV control unit via AV communica-

tion by pressing the “CAMERA” switch of multifunction switch. 

• Around view monitor control unit that receives the camera switch signal supplies the power to each camera

and inputs the camera image from each camera. 

• When the selector lever is in the reverse position, around view monitor control unit receives the reverse sig-

nal, supplies the power to each camera, and inputs the camera image from each camera. 

• Around view monitor control unit that receives the camera image signal from each camera cuts out the

required screen for each view, superimposes the camera image, vehicle icon, guiding lines, sonar indicator,
and outputs them to the display unit. 

CAMERA ASSISTANCE SONAR FUNCTION

• Install the corner sensor on the front bumper and rear bumper. It detects the obstacles around the vehicle

when the around view monitor is displayed. It warns of the approach to the obstacles with the buzzer and
indicator in the display linked with the around view monitor system. 

• It displays the distance between the bumper and obstacle with the color of sonar indicator in the display and

the blinking cycle of indicator in 3 stages. 

• The buzzer warns of the distance to the obstacles with the cycle in 3 stages. 

System Operation Description

• Around view monitor control unit transmits the sonar operation signal via AV communication to sonar control

unit to control the operation of sonar indicator and sonar buzzer. 

• Sonar control unit that receives the sonar operation signal from around view monitor control unit transmits

the detection signal and detection distance signal according to the signal from corner sensor via AV commu-
nication to around view monitor control unit. Around view monitor control unit operates the applicable sonar
indicator. 

• When receiving a sonar operation signal from the around view monitor control unit, the sonar control unit

converts a signal transmitted from the corner sensor into a detection distance signal and transmits it to the
AV control unit via AV communication. When receiving the detection signal, the AV control unit activates
each speaker via BOSE amp.

JSNIA0775GB