Infiniti EX35. Manual - part 884

GW-22

< ON-VEHICLE REPAIR >

FRONT REGULATOR

4.

Draw fully the power window switch in the up direction (auto close position) and hold. Continue holding
the switch even when window is completely closed and then release after more than 2 seconds.

5.

Inspect the anti-pinch system function.
NOTE:
Initialization may be cancelled with continuous opening and closing operation. In this case, initialize the
system.

INSPECT THE FUNCTION OF THE ANTI-PINCH SYSTEM

1.

Fully open the door glass.

2.

Place a wooden piece (wooden hammer handle, etc.) at near fully closed position.

3.

Perform fully closing operation with auto up switch.

• Check that the glass reverses without pinching the wooden piece, is lowered approximately 150 mm (5.906

in) or for more than 2 seconds and then stops.

• The glass should not be raised with power window main switch operated while it is reversing or lowering.

CAUTION:

• Be careful not to be pinched.
• Check that the auto up function is normal before the inspection following the system initialization.

FITTING INSPECTION

• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the

sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.

REAR DOOR GLASS

GW-23

< ON-VEHICLE REPAIR >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

REAR DOOR GLASS

Exploded View

INFOID:0000000003566737

Removal and Installation

INFOID:0000000003566738

REMOVAL

1.

Remove the rear door finisher. Refer to 

INT-17, "Removal and Installation"

.

2.

Remove the rear door inside seal.

3.

Remove the power window switch finisher bracket (1) fixing
bolts (B) and then remove the bracket. 

4.

Disconnect the rear door speaker harness connector (A).

5.

Remove the sealing screen with a cutter tool.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.

1.

Rear door glass run

2.

Corner piece assembly

3.

Power window motor

4.

Regulator assembly

5.

Rear door glass

6.

Rear door inside seal

7.

Sealing screen

8.

Rear door panel

: Vehicle front

JMKIA1950GB

JMKIA1951ZZ

GW-24

< ON-VEHICLE REPAIR >

REAR DOOR GLASS

6.

Remove the TORX bolt fixing the corner piece assembly lower
side to the door panel as shown in the figure with tool (A).

7.

Remove partially the door side weather strip, then remove both screws fixing the corner piece assembly
(1) upper side to the door panel as show in the figure with a screwdriver (A).

8.

Remove the corner piece assembly from the glass upper side.

9.

Reconnect the rear door power window switch.

10. Operate the power window switch to raise/lower the door win-

dow until the glass mounting bolts can be seen.

11. Remove the rear door glass mounting bolts.

12. Remove the rear door glass from inside or outside of door panel.

INSTALLATION

Install in the reverse order of removal.

Inspection and Adjustment

INFOID:0000000003566739

FITTING INSPECTION

• Check that the glass is fit securely into the sash groove.

JMKIA1953ZZ

: Screw

JMKIA1952ZZ

: Bolt

JMKIA1789ZZ

JMKIA0640ZZ

REAR DOOR GLASS

GW-25

< ON-VEHICLE REPAIR >

C

D

E

F

G

H

I

J

L

M

A

B

GW

N

O

P

• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the

sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.