Infiniti EX35. Manual - part 850

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  848  849  850  851   ..

 

 

Infiniti EX35. Manual - part 850

 

 

FAX-30

< ON-VEHICLE REPAIR >

[AWD]

FRONT DRIVE SHAFT

a.

For one-touch clamp band (left side)

i.

Install boot bands securely as shown in the figure.

b.

For low profile type band (right side)

i.

Put boot band in the groove on drive shaft boot. Then fit pawls
(

) into holes to temporary installation.

NOTE:
For the large diameter side, fit projection (A) and guide slit (B) at
first.

ii.

Pinch projection on the band with suitable pliers to tighten band.

iii.

Insert tip of band below end of the pawl.

14. Secure housing and shaft, and then make sure that they are in

the correct position when rotating boot. Install them with boot
band when the mounting positions become incorrect.

15. Install dust cover to housing. (right side)

CAUTION:

Never reuse dust cover.

Inspection

INFOID:0000000003138946

INSPECTION AFTER REMOVAL

• Move joint up/down, left/right, and in the axial directions. Check for motion that is not smooth and for signifi-

cant looseness.

• Check boot for cracks, damage, and leakage of grease.
• Disassemble drive shaft and exchange malfunctioning part if there

is a non-standard condition.

INSPECTION AFTER DISASSEMBLY

Shaft

Check shaft for runout, cracks, or other damage. Replace it if necessary.

Joint Sub-Assembly (Wheel Side)

PDIA1188J

SDIA3557E

SDIA3558E

SDIA1163J

FRONT DRIVE SHAFT

FAX-31

< ON-VEHICLE REPAIR >

[AWD]

C

E

F

G

H

I

J

K

L

M

A

B

FAX

N

O

P

Check the following items, replace the parts if necessary.
• Joint sub-assembly for rough rotation and excessive axial looseness.
• The inside of the joint sub-assembly for entry of foreign material.
• Joint sub-assembly for compression scars, cracks, and fractures inside of joint sub-assembly.
Replace joint sub-assembly if there are any non-standard conditions of components.

Housing and Spider assembly (Final Drive side)

Replace housing and spider assembly if there is scratching or wear of housing roller contact surface or spider
roller contact surface.
NOTE:
Housing and spider assembly are used in a set.

FAX-32

< SERVICE DATA AND SPECIFICATIONS (SDS) 

[AWD]

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS)

Wheel Bearing

INFOID:0000000003138947

Drive Shaft

INFOID:0000000003138948

Item Standard

Axial end play

0.05 mm (0.002 in) or less

Item

Left side

Right side

Grease quantity

Wheel side

77 – 97 g (2.72 – 3.42 oz)

Final drive side

95 – 105 g (3.36 – 3.70 oz)

113 – 123 g (3.99 – 4.33 oz)

Boots installed 
length

Wheel side

136 mm (5.35 in)

Final drive side

152 mm (5.98 in)

158.6 mm (6.24 in)

FL-1

ENGINE

C

D

E

F

G

H

I

J

K

L

M

SECTION 

FL

A

FL

N

O

P

CONTENTS

FUEL SYSTEM

PRECAUTION ...............................................

2

PRECAUTIONS ...................................................

2

General Precautions  .................................................

2

PREPARATION ............................................

3

PREPARATION ...................................................

3

Commercial Service Tools  ........................................

3

ON-VEHICLE MAINTENANCE .....................

4

FUEL SYSTEM  ....................................................

4

Inspection ..................................................................

4

Quick Connector  .......................................................

4

ON-VEHICLE REPAIR ..................................

5

FUEL LEVEL SENSOR UNIT, FUEL FILTER 
AND FUEL PUMP ASSEMBLY  .........................

5

Exploded View ..........................................................

5

Removal and Installation  ..........................................

5

Inspection .................................................................

9

FUEL TANK  ......................................................

10

Exploded View .........................................................

10

Removal and Installation  .........................................

10

Inspection ................................................................

11

SERVICE DATA AND SPECIFICATIONS 
(SDS) ............................................................

13

SERVICE DATA AND SPECIFICATIONS 
(SDS) .................................................................

13

Fuel Tank .................................................................

13

 

 

 

 

 

 

 

Content   ..  848  849  850  851   ..