Infiniti EX35. Manual - part 390

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  388  389  390  391   ..

 

 

Infiniti EX35. Manual - part 390

 

 

CCS

CHIME DOES NOT SOUND

CCS-95

< SYMPTOM DIAGNOSIS >

[INTELLIGENT CRUISE CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

CHIME DOES NOT SOUND

Description

INFOID:0000000003130130

The chime may not sound occasionally in the following cases even if the distance from the vehicle ahead is
short:
• When the speed difference from that of the vehicle ahead is small (both vehicles driving at similar speed).
• When the vehicle ahead drives at faster speed (the actual distance is increasing).
• When depressing the accelerator pedal.
• Chime does not sound when the vehicle ahead is not driving.
• Chime does not sound when the system does not detect any vehicle ahead. (Diagnose the conditions under

which the system is detecting the vehicle ahead and when the system is malfunctioning. If there is any mal-
function in detecting the vehicle ahead, check the system following the 

CCS-98, "Diagnosis Procedure"

).

Diagnosis Procedure

INFOID:0000000003130131

1.

CHECK ICC WARNING CHIME

With CONSULT-III

1.

Start engine.

2.

With “Active Test” of “ICC”, check if “ICC BUZZER” operates normally.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK THE MALFUNCTION SYMPTOM DURING BUZZER OPERATION

Determine preceding vehicle detection status when malfunction occurred. If chime should have sounded:
replace ICC sensor integrated unit and adjust laser beam aiming.

>> INSPECTION END

3.

PERFORM SELF-DIAGNOSIS OF ICC SENSOR INTEGRATED UNIT

1.

Perform self-diagnosis of ICC sensor integrated unit.

2.

Check if DTC “U1000: CAN COMM CIRCUIT” (DTC 100) is detected.

Is any DTC detected?

YES

>> GO TO 4.

NO

>> GO TO 5.

4.

CAN COMMUNICATION INSPECTION

Perform the CAN communication system inspection. Repair or replace applicable item. Refer to 

CCS-75,

"Diagnosis Procedure"

.

>> INSPECTION END

5.

PERFORM SELF-DIAGNOSIS OF UNIFIED METER AND A/C AMP.

1.

Perform self-diagnosis of unified meter and A/C amp.

2.

Check if DTC is detected. Refer to 

MWI-101, "DTC Index"

.

Is any DTC detected?

YES

>> GO TO 7.

NO

>> GO TO 6.

6.

CHECK COMBINATION METER CHIME OPERATION

With CONSULT-III

1.

Select “BUZZER” on “BCM”.

2.

With “Active Test” of “BUZZER”, check if “IGN KEY WARN ALM” and “LIGHT WARN ALM” operate nor-
mally.

Does chime sound?

YES

>> GO TO 8.

CCS-96

< SYMPTOM DIAGNOSIS >

[INTELLIGENT CRUISE CONTROL]

CHIME DOES NOT SOUND

NO

>> Replace combination meter.

7.

REPAIR OR REPLACE APPLICABLE ITEM

Repair or replace applicable item identified by the self-diagnosis result.

>> GO TO 9.

8.

REPLACE ICC SENSOR INTEGRATED UNIT.

1.

Replace ICC sensor integrated unit.

2.

Adjust laser beam aiming. Refer to 

CCS-8, "LASER BEAM AIMING ADJUSTMENT : Special Repair

Requirement (Preparation)"

.

>> GO TO 9.

9.

CHECK ICC SYSTEM

1.

Erase DTC and perform ICC system action test. Then perform self-diagnosis of ICC sensor integrated
unit. (For the details on the ICC system action test, refer to 

CCS-13, "ACTION TEST : Special Repair

Requirement (Vehicle-To-Vehicle Distance Control Mode)"

).

2.

Check that no abnormal condition is present in the ICC system. 

>> INSPECTION END

CCS

DRIVING FORCE IS HUNTING

CCS-97

< SYMPTOM DIAGNOSIS >

[INTELLIGENT CRUISE CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

DRIVING FORCE IS HUNTING

Description

INFOID:0000000003130132

The vehicle causes hunting when the ICC system is active. 

Diagnosis Procedure

INFOID:0000000003130133

1.

PERFORM SELF-DIAGNOSIS OF ECM

1.

Perform self-diagnosis of ECM.

2.

Check if DTC is detected. Refer to 

EC-514, "DTC Index"

.

Is any DTC detected?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK ICC SENSOR INTEGRATED UNIT BODY WINDOW

1.

Check the vehicle driving conditions. Refer to 

CCS-98, "Description"

.

2.

Check ICC sensor integrated unit body window. Refer to 

CCS-98, "Diagnosis Procedure"

.

>> INSPECTION END

3.

REPAIR OR REPLACE APPLICABLE ITEM

Repair or replace applicable item identified by the self-diagnosis result.

>> GO TO 4.

4.

CHECK ICC SYSTEM

1.

Erase DTC and perform ICC system action test. Then perform self-diagnosis of ICC sensor integrated
unit. (For the details on the ICC system action test, refer to 

CCS-13, "ACTION TEST : Special Repair

Requirement (Vehicle-To-Vehicle Distance Control Mode)"

).

2.

Check that no abnormal condition is present in the ICC system. 

>> INSPECTION END

CCS-98

< SYMPTOM DIAGNOSIS >

[INTELLIGENT CRUISE CONTROL]

ICC SYSTEM FREQUENTLY CANNOT DETECT THE VEHICLE AHEAD/ DETEC-

TION ZONE IS SHORT

ICC SYSTEM FREQUENTLY CANNOT DETECT THE VEHICLE AHEAD/
DETECTION ZONE IS SHORT

Description

INFOID:0000000003130134

The detection function may become unstable in the following cases.
• When the reflector of the vehicle ahead is deficient/ not clean enough to reflect the radar.
• When driving a road with extremely sharp corners.
• When the sensor cannot detect the reflector of the vehicle ahead as the vehicle ahead is passing a hill or

passing the peak.

Diagnosis Procedure

INFOID:0000000003130135

1.

VISUAL INSPECTION 1

Check ICC sensor integrated unit body window for contamination and foreign materials.
Is it found?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

REMOVE DIRT AND FOREIGN OBJECTS

Remove any dirt and foreign objects from ICC sensor integrated unit body window. 

>> GO TO 6.

3.

VISUAL INSPECTION 2

Check ICC sensor integrated unit body window for cracks and scratches.
Is it found?

YES

>> GO TO 5.

NO

>> GO TO 4.

4.

ADJUST LASER BEAM AIMING 

1.

Adjust laser beam aiming. Refer to 

CCS-8, "LASER BEAM AIMING ADJUSTMENT : Special Repair

Requirement (Preparation)"

.

2.

Perform ICC system action test. Refer to 

CCS-13, "ACTION TEST : Special Repair Requirement (Vehicle-

To-Vehicle Distance Control Mode)"

.

3.

Check if preceding vehicle detection performance has been improved.

Is it improved?

YES

>> INSPECTION END

NO

>> GO TO 5.

5.

REPLACE ICC SENSOR INTEGRATED UNIT

1.

Replace ICC sensor integrated unit.

2.

Adjust laser beam aiming. Refer to 

CCS-8, "LASER BEAM AIMING ADJUSTMENT : Special Repair

Requirement (Preparation)"

.

>> GO TO 6.

6.

CHECK ICC SYSTEM

1.

Erase DTC and perform ICC system action test. Then perform self-diagnosis of ICC sensor integrated
unit. (For the details on the ICC system action test, refer to 

CCS-13, "ACTION TEST : Special Repair

Requirement (Vehicle-To-Vehicle Distance Control Mode)"

).

2.

Check that no abnormal condition is present in the ICC system. 

>> INSPECTION END

 

 

 

 

 

 

 

Content   ..  388  389  390  391   ..