Infiniti EX35. Manual - part 333

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  331  332  333  334   ..

 

 

Infiniti EX35. Manual - part 333

 

 

C1114 ACTUATOR RELAY SYSTEM

BRC-47

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit).

NO

>> Repair or replace damaged parts.

Component Inspection

INFOID:0000000003430134

1.

CHECK ACTIVE TEST

1.

On “ACTIVE TEST”, select “ABS MOTOR”.

2.

Touch “On” and “Off” on screen. Make sure motor relay and actuator relay operates as shown in table
below.

NOTE:

A brief moment of On/Off condition occurs every 20 seconds after ignition switch turned ON. This is not malfunction because it is
an operation for checking.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-46, "Diagnosis Procedure"

.

Special Repair Requirement

INFOID:0000000003430138

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to 

BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Description"

.

>> END

Test item

Display item

Display

On

Off

ABS MOTOR

MOTOR RELAY

On

Off

ACTUATOR RLY (Note)

On

On

BRC-48

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C1115 WHEEL SENSOR

C1115 WHEEL SENSOR

Description

INFOID:0000000003430125

When the sensor rotor rotates, the magnetic field changes. It converts the magnetic field changes to current
signals (rectangular wave) and transmits them to the ABS actuator and electric unit (control unit). 

DTC Logic

INFOID:0000000003132904

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.

DTC REPRODUCTION PROCEDURE

1.

Start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approximately 1 minute.

2.

Perform ABS actuator and electric unit (control unit) self-diagnosis.

Is DTC “C1115” detected?

YES

>> Proceed to diagnosis. Refer to 

BRC-48, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003430126

CAUTION:

Do not check between wheel sensor terminals.

1.

CHECK TIRES

Check air pressure, wear and size. Refer to 

WT-104, "Tire Air Pressure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts. 

2.

CHECK SENSOR AND SENSOR ROTOR

• Check sensor rotor for damage. 
• Check wheel sensor for damage, disconnection or looseness.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair wheel sensor mount or replace sensor rotor. Then perform the self-diagnosis.

3.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect ABS actuator and electric unit (control unit) connector.

3.

Disconnect wheel sensor connector.

4.

Check terminal to see if it is deformed, disconnected, looseness, etc.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

CHECK WHEEL SENSOR HARNESS

1.

Check the continuity between ABS actuator and electric unit (control unit) harness connector and wheel
sensor harness connector. (Also check continuity when steering wheel is turned right and left and when
sensor harness inside the wheel house is moved.)

DTC

Display item

Malfunction detected condition

Possible cause

C1115

ABS SENSOR
[ABNORMAL SIGNAL]

When wheel sensor input signal is malfunctioning.

• Harness or connector
• Wheel sensor
• ABS actuator and electric unit 

(control unit)

C1115 WHEEL SENSOR

BRC-49

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Measurement terminal for power supply circuit

Measurement terminal for signal circuit

2.

Check the continuity between ABS actuator and electric unit (control unit) harness connector.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Repair or replace damaged parts.

5.

CHECK WHEEL SENSOR POWER SUPPLY CIRCUIT

1.

Connect ABS actuator and electric unit (control unit) connector.

2.

Turn the ignition switch ON.

CAUTION:

Never start the engine.

3.

Check the voltage between wheel sensor harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Repair or replace damaged parts.

6.

CHECK DATA MONITOR

1.

Turn the ignition switch OFF.

2.

Connect each wheel sensor connector.

3.

Check wheel sensor signal. Refer to 

BRC-50, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace ABS actuator and electric unit (control unit).

NO

>> Repair or replace damaged parts.

ABS actuator and electric unit (control unit)

Wheel sensor

Continuity

Connector

Terminal

Connector

Terminal

E41

9

E27 (Front RH)

1

Existed

26

E60 (Front LH)

7

B33 (Rear RH)

6

B34 (Rear LH)

ABS actuator and electric unit (control unit)

Wheel sensor

Continuity

Connector

Terminal

Connector

Terminal

E41

10

E27 (Front RH)

2

Existed

5

E60 (Front LH)

29

B33 (Rear RH)

27

B34 (Rear LH)

ABS actuator and electric unit (control unit)

Continuity

Connector

Terminal

Connector

Terminal

E41

9, 10

E41

1, 4

Not existed

26, 5

7, 29

6, 27

Wheel sensor

Voltage

Connector

Terminal

E27 (Front RH)

1

Ground

8 V or more

E60 (Front LH)

B33 (Rear RH)

B34 (Rear LH)

BRC-50

< COMPONENT DIAGNOSIS >

[VDC/TCS/ABS]

C1115 WHEEL SENSOR

Component Inspection

INFOID:0000000003430127

1.

CHECK DATA MONITOR

On “DATA MONITOR”, select “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR”, and “RR RH SEN-
SOR”, and check the vehicle speed.

NOTE:

Confirm tire pressure is normal.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to diagnosis procedure. Refer to 

BRC-48, "Diagnosis Procedure"

.

Special Repair Requirement

INFOID:0000000003430128

1.

ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION

Always perform the neutral position adjustment for the steering angle sensor, when replacing the ABS actua-
tor and electric unit (control unit). Refer to 

BRC-8, "ADJUSTMENT OF STEERING ANGLE SENSOR NEU-

TRAL POSITION : Description"

.

>> END

Wheel sensor

Condition

Vehicle speed (DATA MONITOR)

FR LH SENSOR

Vehicle stopped

0 [km/h (MPH)]

Vehicle running 
(Note)

Nearly matches the speedometer dis-
play (

±

 10% or less)

FR RH SENSOR

Vehicle stopped

0 [km/h (MPH)]

Vehicle running 
(Note)

Nearly matches the speedometer dis-
play (

±

 10% or less)

RR LH SENSOR

Vehicle stopped

0 [km/h (MPH)]

Vehicle running 
(Note)

Nearly matches the speedometer dis-
play (

±

 10% or less)

RR RH SENSOR

Vehicle stopped

0 [km/h (MPH)]

Vehicle running 
(Note)

Nearly matches the speedometer dis-
play (

±

 10% or less)

 

 

 

 

 

 

 

Content   ..  331  332  333  334   ..