Infiniti EX35. Manual - part 328

EBD

BRC-27

< FUNCTION DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Component Parts Location

INFOID:0000000003430107

For USA

JSFIA0234GB

1.

Steering angle sensor

2.

ABS warning lamp

3.

Brake warning lamp

4.

VDC OFF indicator lamp

5.

SLIP indicator lamp

6.

ABS actuator and electric unit (con-
trol unit)

BRC-28

< FUNCTION DIAGNOSIS >

[VDC/TCS/ABS]

EBD

Except for USA

7.

Front wheel sensor

8.

VDC OFF switch

9.

Yaw rate/side G sensor

10. Rear wheel sensor

A.

Back of spiral cable assembly

B.

Combination meter

C.

Inside brake master cylinder cover

D.

Steering knuckle

E.

Instrument driver lower panel

F.

Under center console

G.

Rear final drive assembly

JSFIA0235GB

EBD

BRC-29

< FUNCTION DIAGNOSIS >

[VDC/TCS/ABS]

C

D

E

G

H

I

J

K

L

M

A

B

BRC

N

O

P

Component Description

INFOID:0000000003430108

1.

Steering angle sensor

2.

ABS warning lamp

3.

Brake warning lamp

4.

VDC OFF indicator lamp

5.

SLIP indicator lamp

6.

ABS actuator and electric unit (con-
trol unit)

7.

Front wheel sensor

8.

VDC OFF switch

9.

Yaw rate/side G sensor

10. Rear wheel sensor

A.

Back of spiral cable assembly

B.

Combination meter

C.

Inside brake master cylinder cover

D.

Steering knuckle

E.

Instrument driver lower panel

F.

Under center console

G.

Rear final drive assembly

Component parts

Reference

ABS actuator and electric unit (control unit)

Pump

BRC-44, "Description"

Motor

Actuator relay (main relay)

BRC-46, "Description"

Solenoid valve

BRC-53, "Description"

Pressure sensor

BRC-58, "Description"

VDC switch-over valve
(USV1, USV2, HSV1, HSV2)

BRC-66, "Description"

Wheel sensor

BRC-35, "Description"

Yaw rate/side G sensor

BRC-63, "Description"

Steering angle sensor

BRC-60, "Description"

VDC OFF switch

BRC-79, "Description"

ABS warning lamp

BRC-81, "Description"

Brake warning lamp

BRC-82, "Description"

VDC OFF indicator lamp

BRC-83, "Description"

SLIP indicator lamp

BRC-84, "Description"

BRC-30

< FUNCTION DIAGNOSIS >

[VDC/TCS/ABS]

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL 

UNIT)]

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]

CONSULT-III Function

INFOID:0000000003132875

FUNCTION

CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

WORK SUPPORT

CAUTION:

Erase DTC memory of the lane camera unit after implementing work support. Refer to 

CCS-130, "CON-

SULT-III Function (LANE CAMERA)"

.

SELF DIAGNOSTIC RESULT

Operation Procedure

Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute.

Display Item List

Refer to 

BRC-95, "DTC No. Index"

.

How to Erase Self-diagnosis Results

After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute as the final inspection, and make sure that the ABS warning lamp, VDC OFF indicator lamp,
SLIP indicator lamp and brake warning lamp turn OFF.

CAUTION:

If memory cannot be erased, perform applicable diagnosis.
NOTE:
• When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp, VDC

OFF indicator lamp, SLIP indicator lamp and brake warning lamp will not turn OFF even when the system is
normal unless the vehicle is driven at approximately 30 km/h (19 MPH) or more for approximately 1 minute.

• Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake

fluid level switch operation (when brake fluid is insufficient).

• VDC OFF switch should not stay in “ON” position.

DATA MONITOR

Display Item List

Diagnostic test mode

Function

Work support

This mode enables a technician to adjust some devices faster and more accurately by following 
the indications on CONSULT-III.

Self diagnostic result

Self-diagnostic results can be read and erased quickly.

Data monitor

Input/Output data in the ABS actuator and electric unit (control unit) can be read.

Active test

CONSULT-III drives some actuators apart from ABS actuator and electric unit (control unit) and 
also shifts some parameters in a specified range.

ECU identification

ABS actuator and electric unit (control unit) part number can be read.

Item

Description

ST ANG SEN ADJUSTMENT

Adjusts the neutral position of the steering angle sensor.