Infiniti EX35. Manual - part 1464

TM-244

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

54. Apply recommended sealant (Genuine RTV Silicone Sealant or

equivalent. Refer to 

GI-15, "Recommended Chemical Products

and Sealants"

.) to oil pump assembly as shown in the figure.

CAUTION:

Completely remove all moisture, oil and old sealant, etc.
from the oil pump mounting bolts and oil pump mounting
bolt mounting surfaces.

55. Tighten oil pump bolts to the specified torque.

CAUTION:

Apply ATF to oil pump bushing.

56. Install O-ring to input clutch assembly.

57. Install converter housing to transmission case, and then tighten

converter housing bolts (A) and self-sealing bolt (B) to the spec-
ified torque.

58. Make sure that brake band (A) does not close turbine revolution

sensor hole (B).

SCIA5321E

SCIA2300E

SCIA5011E

SCIA8085E

JPDIA0020ZZ

TRANSMISSION ASSEMBLY

TM-245

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

59. Connect TCM connector (A) and park/neutral position switch

connector (B).

60. Install A/T assembly harness connector (A) to control valve with

TCM.

61. Connect TCM connectors (A) and (B).

62. Install O-ring (1) to A/T assembly harness connector (A).

63. Install bracket (1) to A/T fluid temperature sensor 2 (2).

JPDIA0018ZZ

JPDIA0019ZZ

JPDIA0016ZZ

JPDIA0015ZZ

JPDIA0014ZZ

TM-246

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

TRANSMISSION ASSEMBLY

64. Install A/T fluid temperature sensor 2 (1) [with bracket (2)] in

control valve with TCM. Tighten A/T fluid temperature sensor 2
bolt to the specified torque.

CAUTION:

Adjust bolt hole of bracket to bolt hole of control valve.

65. Install control valve with TCM in transmission case.

CAUTION:

• Make sure that turbine revolution sensor securely installs

turbine revolution sensor hole (B). 

• Hang down revolution sensor harness toward outside so

as not to disturb installation of control valve with TCM.

• Adjust A/T assembly harness connector of control valve

with TCM to terminal hole of transmission case.

• Assemble it so that manual valve cutout is engaged with

manual plate projection.

66. Install bolts (A), (B) and (C) in control valve with TCM. Tighten

bolt 1, 2 and 3 temporarily to prevent dislocation. After that
tighten them in order (1 

→

 2 

→

 3), and then tighten other bolts.

Tighten control valve with TCM bolts to the specified torque.

JPDIA0013ZZ

A

: Brake band

JPDIA0020ZZ

SCIA5035E

: Front

Bolt symbol

A

B

C

Number of bolts

5

6

1

Length

mm (in)

42 (1.65)

55 (2.17)

40 (1.57)

Tightening torque

N·m (km-g, in-lb)

7.9 (0.81, 70)

With ATF applied

7.9 (0.81, 70)

SCIA8078E

TRANSMISSION ASSEMBLY

TM-247

< DISASSEMBLY AND ASSEMBLY >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

67. Connect A/T fluid temperature sensor 2 connector (A).

68. Engage terminal cord assembly and A/T fluid temperature sen-

sor 2 harness with terminal clips (

).

69. Connect revolution sensor connector (A).
70. Engage revolution sensor harness with terminal clip (

).

71. Pull down A/T assembly harness connector.

CAUTION:

Be careful not to damage connector.

72. Install snap ring to A/T assembly harness connector.

73. Install magnets (1) in oil pan.

SCIA8124E

JPDIA0011ZZ

SCIA5299E

SCIA5300E

JPDIA0009ZZ