Infiniti EX35. Manual - part 1416

TM-52

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0717 TURBINE REVOLUTION SENSOR

P0717 TURBINE REVOLUTION SENSOR

Description

INFOID:0000000003130484

The turbine revolution sensor detects input shaft rpm (revolutions per minute). It is located on the input side of
the A/T. Monitors revolution of sensor 1 and sensor 2 for non-standard conditions.

DTC Logic

INFOID:0000000003130485

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.

1.

CHECK DTC DETECTION

 With CONSULT-III

1.

Start the engine.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

 With GST

Follow the procedure “With CONSULT-III”.

Is “P0717 TURBINE REV S/CIRC” detected?

YES

>> Go to 

TM-52, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-38, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003130486

1.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-89, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> Replace the control valve with TCM. Refer to 

TM-162, "Exploded View"

.

NO

>> Repair or replace damaged parts.

DTC

Item

(CONSULT-III screen 

terms)

A/T CHECK indicator 
lamp judgment flicker

Diagnostic item is de-

tected when...

Possible cause

P0717

TURBINE REV S/CIRC

11th

• TCM does not receive 

the proper voltage sig-
nal from the sensor.

• TCM detects an irreg-

ularity only at position 
of 4th gear for turbine 
revolution sensor 2.

• Harness or connectors

(Sensor circuit is open 
or shorted.)

• Turbine revolution 

sensor 1 and/or 2

VHCL/S SE-A/T

: 40 km/h (25 MPH) or more

ACCELE POSI

: More than 0.5/8

ENGINE SPEED

: 1,500 rpm or more

SLCT LVR POSI

: “D” position

GEAR (Turbine revo-
lution sensor 1)

: “4” or “5” position

GEAR (Turbine revo-
lution sensor 2)

: All positions

Driving location

: Driving the vehicle uphill (increased engine load) will help maintain the driving con-
ditions required for this test.

P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)

TM-53

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)

Description

INFOID:0000000003130487

The revolution sensor detects the revolution of the parking gear and emits a pulse signal. The pulse signal is
transmitted to the TCM which converts it into vehicle speed.

DTC Logic

INFOID:0000000003130488

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION:

• Always drive vehicle at a safe speed.
• Be careful not to rev engine into the red zone on the tachometer.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch
OFF. Then wait at least 10 seconds before performing the next test.

1.

CHECK REVOLUTION SENSOR AND VEHICLE SPEED SENSOR MTR

 With CONSULT-III

1.

Start the engine.

2.

Select “Data Monitor” mode for “TRANSMISSION”.

3.

Drive vehicle and check for an increase of “VHCL/S SE-A/T” value in response to “VHCL/S SE-MTR”
value.

Are “VHCL/S SE-A/T” and “VHCL/S SE-MTR” values correct?

YES

>> GO TO 2.

NO

>> Go to 

TM-54, "Diagnosis Procedure"

.

2.

CHECK DTC DETECTION 1

 With CONSULT-III

1.

Select “Data Monitor” mode for “TRANSMISSION”.

2.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

 With GST

DTC

Item

(CONSULT-III screen 

terms)

A/T CHECK indicator 
lamp judgment flicker

Diagnostic item is de-

tected when...

Possible cause

P0720

VEH SPD SEN/CIR AT

1st

• Signal from vehicle 

speed sensor A/T 
(revolution sensor) not 
input due to cut line or 
the like.

• Unexpected signal in-

put during running.

• After ignition switch is 

turned ON, unexpect-
ed signal input from 
vehicle speed sensor 
MTR before the vehi-
cle starts moving.

• Harness or connectors

(Sensor circuit is open 
or shorted.)

• Revolution sensor
• Vehicle speed sensor 

MTR

VHCL/S SE-A/T

: Approximately matches the speedometer reading.

VHCL/S SE-MTR

: Approximately matches the speedometer reading.

VHCL/S SE-A/T

: 30 km/h (19 MPH) or more

ACCELE POSI

: More than 1.0/8

SLCT LVR POSI

: “D” position

Drive location

: Driving the vehicle uphill (increased engine load) will help maintain the driving condi-
tions required for this test.

TM-54

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)

Follow the procedure “With CONSULT-III”.

Is “P0720 VEH SPD SEN/CIR AT” detected?

YES

>> Go to 

TM-54, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

CHECK DTC DETECTION 2

 With CONSULT-III

1.

Select “Data Monitor” mode for “TRANSMISSION”.

2.

Drive vehicle and maintain the following conditions for at least 5 consecutive seconds.

 With GST

Follow the procedure “With CONSULT-III”.

Is “P0720 VEH SPD SEN/CIR AT” detected?

YES

>> Go to 

TM-54, "Diagnosis Procedure"

.

NO

>> Check intermittent incident. Refer to 

GI-38, "Intermittent Incident"

.

Diagnosis Procedure

INFOID:0000000003130489

1.

CHECK TCM POWER SUPPLY AND GROUND CIRCUIT

Check TCM power supply and ground circuit. Refer to 

TM-89, "Diagnosis Procedure"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace damaged parts.

2.

CHECK SUB-HARNESS

1.

Disconnect park/neutral position switch connector and TCM connector.

2.

Check continuity between park/neutral position switch connector terminals and TCM connector terminals.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace damaged parts.

3.

DETECT MALFUNCTIONING ITEM

Check the following.
• Check terminals of park/neutral position switch connector and TCM connector, and harness cladding for

damage.

• Check connector for loose connection.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace damaged parts.

4.

REPLACE THE REVOLUTION SENSOR AND CHECK DTC

1.

Replace the revolution sensor. Refer to 

TM-180, "2WD : Exploded View"

 (2WD) or 

TM-198, "Exploded

View"

, 

TM-208, "Disassembly"

 (AWD).

2.

Reinstall any parts removed.

ACCELE POSI

: More than 1.0/8

ENGINE SPEED

: 3,500 rpm or more

SLCT LVR POSI

: “D” position

Drive location

: Driving the vehicle uphill (increased engine load) will help maintain the driving condi-
tions required for this test.

Park/neutral position switch connector

TCM connector

Continuity

Connector

Terminal

Connector

Terminal

F154

8

F152

20

Existed

9

17

10

16

P0720 VEHICLE SPEED SENSOR A/T (REVOLUTION SENSOR)

TM-55

< COMPONENT DIAGNOSIS >

[5AT: RE5R05A]

C

E

F

G

H

I

J

K

L

M

A

B

TM

N

O

P

3.

Perform “DTC CONFIRMATION PROCEDURE”. Refer to 

TM-53, "DTC Logic"

.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace the control valve with TCM. Refer to 

TM-162, "Exploded View"

.