Infiniti EX35. Manual - part 1356

SRC-50

< COMPONENT DIAGNOSIS >

B1065, B1070 ASSIST A/B MODULE

B1065, B1070 ASSIST A/B MODULE

Description

INFOID:0000000003591782

DTC B 1065, B1070 [OPEN] ASSIST A/B MODULE

For front passenger air bag module, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision whose acceleration exceeds the specified level, the ignition materials are
ignited by electric ignition system. The system burns and introduces the chemical reaction of gas generating
materials to generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front passenger air bag module is installed on the instrument panel with fixed bolts.

DTC Logic

INFOID:0000000003591783

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-50, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003591784

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1065
B1070

ASSIST A/B MODULE 
[OPEN]

Front passenger air bag module circuit 
is open

• Disconnection of wiring harness and 

open

• Internal breakdown in front passen-

ger air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1065, B1070 ASSIST A/B MODULE

SRC-51

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK FRONT PASSENGER AIR BAG MODULE

1.

Replace front passenger air bag module. Refer to 

SR-8, "Exploded View"

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-50, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-4, "Exploded View"

.

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-50, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END

SRC-52

< COMPONENT DIAGNOSIS >

B1066, B1071 ASSIST A/B MODULE

B1066, B1071 ASSIST A/B MODULE

Description

INFOID:0000000003591785

DTC B1066, B1071 [VB-SHORT] ASSIST A/B MODULE

For front passenger air bag module, crash is judged by main “G” sensor output signal and Safing algorithm in
front direction.

OPERATION

In the case of a frontal collision whose acceleration exceeds the specified level, the ignition materials are
ignited by electric ignition system. The system burns and introduces the chemical reaction of gas generating
materials to generate hot gases that flow into the air bag through a filter and expand the bag.

STRUCTURE

Front passenger air bag module mainly consists of air bag and inflator which inflates air bag.

INSTALLATION

Front passenger air bag module is installed on the instrument panel with fixed bolts.

DTC Logic

INFOID:0000000003591786

DTC DETECTION LOGIC

With CONSULT-III

DTC No. Index (“SELF-DIAG [CURRENT]”), (“SELF-DIAG [PAST]” or “TROUBLE DIAG RECORD”)

DTC CONFIRMATION PROCEDURE (WITH CONSULT-III)

1.

CHECK SELF-DIAG RESULT

1.

Turn ignition switch ON.

2.

Check the screen of CONSULT-III.

Is malfunctioning part detected?

YES

>> Refer to 

SRC-52, "Diagnosis Procedure"

.

NO

>> INSPECTION END

DTC CONFIRMATION PROCEDURE (WITHOUT CONSULT-III)

NOTE:
• SRS will not enter diagnosis mode if no malfunction is detected in user mode.

1.

CHECK AIR BAG WARNING LAMP

1.

Turn ignition switch ON.

2.

Check the air bag warning lamp status.

Is malfunctioning part detected?

YES

>> Refer to warning lamp flash code chart. Refer to 

SRC-128, "DTC Index"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000003591787

WITH CONSULT-III

WARNING:

• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait at least 3

minutes. (To discharge backup capacitor.)

• Do not use unspecified tester or other measuring device.

DTC No.

Trouble diagnosis name

DTC detecting condition

Possible cause

B1066
B1071

ASSIST A/B MODULE 
[VB-SHORT]

Front passenger air bag module circuit 
is shorted to some power supply circuit

• Disconnection of wiring harness and 

short

• Internal breakdown in front passen-

ger air bag module

• Internal breakdown in air bag diag-

nosis sensor unit

B1066, B1071 ASSIST A/B MODULE

SRC-53

< COMPONENT DIAGNOSIS >

C

D

E

F

G

I

J

K

L

M

A

B

SRC

N

O

P

DIAGNOSTIC PROCEDURE

1.

CHECK HARNESS CONNECTOR

Check the connection of harness connector.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace harness connector.

2.

CHECK WIRING HARNESS

Check the wiring harness externals.
Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Replace wiring harness.

3.

CHECK FRONT PASSENGER AIR BAG MODULE

1.

Replace front passenger air bag module. Refer to 

SR-8, "Exploded View"

.

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-52, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 4.

NO

>> INSPECTION END

4.

CHECK AIR BAG DIAGNOSIS SENSOR UNIT

1.

Replace air bag diagnosis sensor unit. Refer to 

SR-4, "Exploded View"

.

2.

Check “Self diagnostic result” with CONSULT-III.

3.

Perform DTC confirmation procedure. Refer to 

SRC-52, "DTC Logic"

.

Is DTC detected?

YES

>> GO TO 1.

NO

>> INSPECTION END