Infiniti EX35. Manual - part 1136

 

  Index      Infiniti     Infiniti EX35 - service repair manual 2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1134  1135  1136  1137   ..

 

 

Infiniti EX35. Manual - part 1136

 

 

PCS

DIAGNOSIS SYSTEM (BCM)

PCS-45

< FUNCTION DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

REQ SW -RL

NOTE:
This item is displayed, but cannot be monitored. 

REQ SW -BD/TR

Indicates [ON/OFF] condition of back door request switch.

PUSH SW

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY2 -F/B

Indicates [ON/OFF] condition of ignition relay 2.

CLUCH SW

NOTE:
This item is displayed, but cannot be monitored. 

BRAKE SW 1

Indicates [ON/OFF] condition of brake switch.

DETE/CANCL SW

Indicates [ON/OFF] condition of P position.

SFT PN/N SW

Indicates [ON/OFF] condition of P or N position.

S/L -LOCK

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L -UNLOCK

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY -F/B

Indicates [ON/OFF] condition of ignition switch.

UNLK SEN -DR

Indicates [ON/OFF] condition of driver door UNLOCK status.

PUSH SW -IPDM

Indicates [ON/OFF] condition of push-button ignition switch.

IGN RLY1 -F/B

Indicates [ON/OFF] condition of ignition relay 1.

DETE SW -IPDM

Indicates [ON/OFF] condition of P position.

SFT PN -IPDM

Indicates [ON/OFF] condition of P or N position.

SFT P -MET

Indicates [ON/OFF] condition of P position.

SFT N -MET

Indicates [ON/OFF] condition of N position.

ENGINE STATE

Indicates [STOP/START/CRANK/RUN] condition of engine states.

S/L LOCK-IPDM

Indicates [ON/OFF] condition of steering lock unit (LOCK).

S/L UNLK-IPDM

Indicates [ON/OFF] condition of steering lock unit (UNLOCK).

S/L RELAY-REQ

Indicates [ON/OFF] condition of steering lock relay.

VEH SPEED 1

Display the vehicle speed signal received from combination meter by numerical value [Km/h].

VEH SPEED 2

Display the vehicle speed signal received from ABS or VDC or CVT by numerical value [Km/h].

DOOR STAT-DR

Indicates [LOCK/READY/UNLOCK] condition of driver side door status.

DOOR STAT-AS

Indicates [LOCK/READY/UNLOCK] condition of passenger side door status.

ID OK FLAG

Indicates [SET/RESET] condition of key ID.

PRMT ENG STRT

Indicates [SET/RESET] condition of engine start possibility.

PRMT RKE STRT

NOTE:
This item is displayed, but cannot be monitored. 

KEY SW -SLOT

Indicates [ON/OFF] condition of key slot.

TRNK/HAT MNTR

NOTE:
This item is displayed, but cannot be monitored. 

RKE-LOCK

Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.

RKE-UNLOCK

Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.

RKE-TR/BD

NOTE:
This item is displayed, but cannot be monitored. 

RKE-PANIC

Indicates [ON/OFF] condition of PANIC button of Intelligent Key.

RKE-P/W OPEN

Indicates [ON/OFF] condition of P/W DOWN signal from Intelligent Key.

RKE-MODE CHG

Indicates [ON/OFF] condition of MODE CHANGE signal from Intelligent Key.

RKE OPE COUN1

When remote keyless entry receiver receives the signal transmitted while operating on Intelligent Key, the 
numerical value start changing.

RKE OPE COUN2

NOTE:
This item is displayed, but cannot be monitored. 

Monitor Item

Condition

PCS-46

< FUNCTION DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

DIAGNOSIS SYSTEM (BCM)

ACTIVE TEST

Test item

Description

BATTERY SAVER

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

PW REMOTO DOWN SET

This test is able to check power window down operation.
The power window down will be activated after “ON” on CONSULT-III screen is touched.

INSIDE BUZZER

This test is able to check warning chime in combination meter operation.
• Take away warning chime sounds when “TAKE OUT” on CONSULT-III screen is touched.
• Key warning chime sounds when “KEY WARN” on CONSULT-III screen is touched.
• P position warning chime sounds when “P RNG WARN” on CONSULT-III screen is touched.
• ACC warning chime sounds when “ACC WARN” on CONSULT-III screen is touched.

OUTSIDE BUZZER

This test is able to check Intelligent Key warning buzzer operation.
The Intelligent Key warning buzzer will be activated after “ON” on CONSULT-III screen is touched.

INDICATOR

This test is able to check warning lamp operation.
• “KEY” Warning lamp illuminates when “RED ON” on CONSULT-III screen is touched.
• “KEY” Warning lamp flashes when “RED IND” on CONSULT-III screen is touched.

INT LAMP

This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.

LCD

This test is able to check meter display information
• Engine start information displays when “B&P N” on CONSULT-III screen is touched.
• Engine start information displays when “B&P I” on CONSULT-III screen is touched.
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched.
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched.
• P position warning displays when “SFT P” on CONSULT-III screen is touched.
• Intelligent Key insert information displays when “INSRT” on CONSULT-III screen is touched.
• Intelligent Key low battery warning displays when “BATT” on CONSULT-III screen is touched.
• Take away through window warning displays when “NO KY” on CONSULT-III screen is touched.
• Take away warning display when “OUTKY” on CONSULT-III screen is touched.
• OFF position warning display when “LK WN” on CONSULT-III screen is touched.

TRUNK/GLASS HATCH

This test is able to check back door opener actuator open operation.
This actuator opens when “ON” on CONSULT-III screen is touched.

FLASHER

This test is able to check security hazard lamp operation.
The hazard lamps will be activated after “ON” on CONSULT-III screen is touched.

HORN

This test is able to check horn operation.
The horn will be activated after “ON” on CONSULT-III screen is touched.

IGN CONT2

This test is able to check ignition relay operation.
The ignition relay will be activated after “ON” on CONSULT-III screen is touched.

P RANGE

This test is able to check control device power supply
Control device power is supplied when “ON” on CONSULT-III screen is touched.

ENGINE SW ILLUMI

This test is able to check push-ignition switch illumination operation.
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched.

LOCK INDICATOR

This test is able to check LOCK indicator in push-ignition switch operation.
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

ACC INDICATOR

This test is able to check ACC indicator in push-ignition switch operation.
ACC indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

IGNITION ON IND

This test is able to check ON indicator in push-ignition switch operation.
ON Indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is touched.

KEY SLOT ILLUMI

This test is able to check key slot illumination operation.
Key slot illumination flash when “ON” on CONSULT-III screen is touched.

AUTOMATIC BACK DOOR

NOTE:
This item is displayed, but cannot be tested.

AUTOMATIC SLIDING DOOR

NOTE:
This item is displayed, but cannot be tested.

PCS

U1000 CAN COMM CIRCUIT

PCS-47

< COMPONENT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

COMPONENT DIAGNOSIS

U1000 CAN COMM CIRCUIT

Description

INFOID:0000000003657653

CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Modern
vehicle is equipped with many electronic control unit, and each control unit shares information and links with
other control units during operation (not independent). In CAN communication, control units are connected
with 2 communication lines (CAN H-line, CAN L-line) allowing a high rate of information transmission with less
wiring. Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to 

LAN-27, "CAN Communication Signal Chart"

.

DTC Logic

INFOID:0000000003657654

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000003657655

1.

PERFORM SELF DIAGNOSTIC

1.

Turn ignition switch ON and wait for 2 seconds or more.

2.

Check “Self Diagnostic Result”.

Is “U1000: CAN COMM CIRCUIT” displayed?

YES

>> Refer to 

LAN-18, "Trouble Diagnosis Flow Chart"

.

NO

>> Refer to 

GI-38, "Intermittent Incident"

.

DTC

CONSULT-III display 

description

DTC Detection Condition

Possible cause

U1000

CAN COMM CIRCUIT

When BCM cannot communicate CAN com-
munication signal continuously for 2 seconds 
or more.

CAN communication system

PCS-48

< COMPONENT DIAGNOSIS >

[POWER DISTRIBUTION SYSTEM]

U1010 CONTROL UNIT (CAN)

U1010 CONTROL UNIT (CAN)

DTC Logic

INFOID:0000000003657656

DTC DETECTION LOGIC

Diagnosis Procedure

INFOID:0000000003657657

1.

REPLACE BCM

When DTC “U1010: CONTROL UNIT (CAN)” is detected, replace BCM.

>> Replace BCM. Refer to 

BCS-84, "Exploded View"

.

Special Repair Requirement

INFOID:0000000003657658

1.

REQUIRED WORK WHEN REPLACING BCM

Initialize control unit. Refer to CONSULT-III operation manual NATS-IVIS/NVIS.

>> Work end.

DTC

CONSULT-III display de-

scription

DTC Detection Condition

Possible cause

U1010

CONTROL UNIT (CAN)

BCM detected internal CAN communication circuit malfunction.

BCM

 

 

 

 

 

 

 

Content   ..  1134  1135  1136  1137   ..