Porshe 911 (997). Manual - part 915

During programming, it is essential to guarantee the power supply for the Porsche System tester. It is
essential to connect a battery charger with a current rating of at least 40 A to the vehicle battery.

→ Prior to disconnecting the control module, switch off the ignition and remove the ignition key.

Note

Follow the instructions on the Tester.
Later versions of the software may display slightly different text or require a slightly different procedure. The
instructions you receive from the tester itself take precedence over this description.

1. Connect the Porsche System Tester to the vehicle and start the System Tester. Switch on the ignition. >>

Continue.

2. Select the vehicle type.

3. Using the >> key, move from Vehicle type to the list of Control units and perform the automatic control

unit search.

4. Select PCM2 with the cursor keys and press the >> key.

5. Select External BOSE amplifier with the cursor keys and press the >>

key.

6. Select Coding using the cursor keys and press >> .

7. Select Read out coding (codings) with the cursor keys and press

>> .

8. Switch to the Special functions menu and perform the vehicle handover using the F8 key.

9. In the Special functions menu, erase All fault memories by pressing

>> .

10. Carry out automatic search of control units.

11. In the menu Write in coding >> , the data read out are installed.

12. In Coding select the version and follow the instructions of the

Tester.

13. Read out and erase fault memory.

Coding the BOSE loudspeaker amplifier

WARNING

Sudden voltage interruption of the power supply to the control module.

Destruction of the control module.

• 

→ During programming, it is essential to guarantee the power supply for the Porsche System tester. It is

essential to connect a battery charger with a current rating of at least 40 A to the vehicle battery.

→ Prior to disconnecting the control module, switch off the ignition and remove the ignition key.

Diagnostic system: reading out fault memory and activating systems

Reading out and writing to the BOSE loudspeaker amplifier

3817

Note

Follow the instructions on the Tester.
Later versions of the software may display slightly different text or require a slightly different procedure. The
instructions you receive from the tester itself take precedence over this description.

Note

The PCM 2 code from the IPAS is needed for coding the loudspeaker amplifier.

1. Connect the Porsche System Tester to the vehicle and start the System Tester. Switch on the ignition. >>

Continue.

2. Select vehicle type using the cursor keys.

3. Using the >> key, move from the vehicle type to the list of control modules. Perform the automatic

control module search.

4. Select the relevant control module with the cursor keys and press the >>

key.

5. Select Coding using the cursor keys and press >> .

6. Select the version required for the vehicle in question, code it with F8 and follow the instructions on

the Tester.

Vehicle type vehicle coding

911 (997)

Boxster (987)

Vehicle version vehicle coding

Coupé

Cabriolet

Targa

Right/left-hand drive vehicle coding

Left-hand drive

Right-hand drive

Bass box

Normal bass box

Large bass box (50l)

PCM 2 code

Enter PCM 2 code

7. In the menu Vehicle type, select Control units and then select the menu Special functions.

8. PerformVehicle handover and follow the instructions of the tester.

9. Read out and erase fault memory.

997410, 997411, 997430, 997431, 997610, 997611, 997620, 997621

Diagnostic system: reading out fault memory and activating systems

Coding the BOSE loudspeaker amplifier

3818

C23, C24, C25, C26, C27, C28, C32, C33, C34, C35, C36, C37, C38, C39, C45, C46, C98, C99

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Diagnostic system: reading out fault memory and activating systems

Coding the BOSE loudspeaker amplifier

3819

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Coding the BOSE loudspeaker amplifier

3820