Porshe 911 (997). Manual - part 694

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  692  693  694  695   ..

 

 

Porshe 911 (997). Manual - part 694

 

 

Triggering roll-over protection system

ATTENTION

Danger of injury when working on the roll-over protection system!

→ The movement range of the roll-over protection system must be kept

clear.

4. Check roll-over protection system (function test). Select menu item Roll-over protection, and select

menu item Drive links in the command line which then appears. Press the key combination
described in the tester; the roll-over protection system is triggered.

Press in the roll-over bar

5. Press locking levers outward -Arrow A- and press in the roll-over bar -1- -Arrow B- until it is felt to

engage -inset- .

Subsequent work

Subsequent work

1. Install rear wall trim panel → 703119 23 Removing and installing trim panel for rear wall - chapter

on "Installing"

2. Install cover for rear → 705319 23 Removing and installing cover for rear - chapter on "Installing"

997610

Diagnostic system: reading out fault memory and activating systems

 Subsequent work

2933

C23, C24, C25, C26, C27, C28, C32, C33, C34, C35, C36, C37, C38, C39, C45, C46, C98, C99

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2934

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2935

- Preliminary work
- Removing frame for roll-over protection system
- Installing frame for roll-over protection system
- Subsequent work

Preliminary work

Preliminary work

1. Removing rear wall trim panel → 703119 Removing and installing trim panel for rear wall - section on

"Removing"  [997310 997311 997320 997321]→ 703119 21 Removing and installing trim panel for rear
wall - section on "Removing"  [997610 997611 997620 997621]

2. Remove cover for the rear. → 705319 Removing and installing cover for rear - section on

"Removing"  [997310 997311 997320 997321]→ 705319 21 Removing and installing cover for rear
- section on "Removing"  [997610 997611 997620 997621]

3. Remove rear side trim panel at left and right. → 707519 Removing and installing rear side trim panel -

section on "Removing"

4. Undo seat belt and rear mounting component at the left and right. → 691219 Removing and installing rear

three-point belt - section on "Removing"

5. Trigger the roll-over bar. → 697219 Removing and installing roll-over bar - section on

"Removing" [997610]→ 697219 Removing and installing roll-over bar - section on "Removing" [997310
997311 997320 997321 997611 997620 997621]

Note

Do not loosen hydraulic lines at hydraulic pump.

6. Remove hydraulic pump and set it aside. . → 618419 Removing and installing hydraulic pump - section on

"Removing"

7. Unlock plug connections for DME control module. → 247019 Removing and installing DME

control module - section on "Removing" [997310 997311 997320 997321 997611 997620
997621]→ 247019 Removing and installing DME control module - section on
"Removing" [997610]

8. Unlock plug connections for convertible-top control unit. → 619619 Removing and installing

control unit for convertible top - section on "Removing"

9. Release relay carrier and set it aside. → 979019 Removing and installing relay carrier - section on

"Removing"

10. Remove motor for drive mechanism and set it aside. → 617019 Removing and installing motor for drive

mechanism - section on "Removing"

2936

 

 

 

 

 

 

 

Content   ..  692  693  694  695   ..