Porshe 911 (997). Manual - part 673

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  671  672  673  674   ..

 

 

Porshe 911 (997). Manual - part 673

 

 

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2849

correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2850

69 51 19 Removing and installing airbag sensor - as
of MY 2005

- Preliminary work
- General warning notes
- Tools and materials
- Removing airbag sensor
- Installing airbag sensor
- Reworking

Tools

Designation

Type

Number

Explanation

PIWIS Tester

special tool

97180

Removal tool, universal commercially

available tool

NR.21

Preliminary work

Preliminary work for front airbag sensor

1. Disconnect battery. →   Work instructions after disconnecting the battery

2. Remove front apron. → 631519 Removing and installing front apron - chapter on "Removing"

2851

Preliminary work for centre airbag sensor

1. Disconnect battery. →   Work instructions after disconnecting the battery

2. Remove front seat. →   Removing and installing front

seat

3. Remove the rear side-panel lining. → 707519 Removing and installing rear side-panel

lining [997310 997311 997320 997321 997610 997611 997620 997621]→ 707519 Removing and
installing rear side-panel lining [997110 997111 997120 997121 997410 997411 997430 997431]

4. Remove sill. → 680519 Removing and installing inner sill

5. Undo screw fastening seat belt to the body. → 691119 21 Removing and installing front three-point belt -

removing

General warning notes

Safety instructions for airbag sensor

ATTENTION

Incorrect triggering of airbag modules.

Danger of injury and material damage if airbag sensors are not handled correctly!

• 

→ Remove ignition key. Disconnect battery. Route or isolate ground strap so that all contact with a ground

carrier (e.g. body, seat frame) is avoided.

→ Always wait one minute after disconnecting the battery before disconnecting the connector from the

sensor.

→ The airbag sensor must not be removed with the plug plugged in!

→ The airbag sensors cannot be interchanged. Install the sensor listed in the Spare Parts Catalogue (PET).

→ Always replace fastening nuts and bolts of sensors after customer service and reworking.

→ Never make alterations to the micro-encapsulated nuts and bolts which have a negative effect on the bond

(e.g. using lubricant, loosening bolts and screwing them down again).

Tools and materials

Diagnostic system: reading out fault memory and activating systems

Preliminary work for centre airbag sensor

2852

 

 

 

 

 

 

 

Content   ..  671  672  673  674   ..