Porshe 911 (997). Manual - part 672

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  670  671  672  673   ..

 

 

Porshe 911 (997). Manual - part 672

 

 

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2845

- Preliminary work
- Removing adjustment fitting (seat belt height adjuster)
- Installing adjustment fitting (seat belt height adjuster)
- Subsequent work

Preliminary work

Preliminary work

Remove B-pillar trim. → 706719 Removing and installing B-pillar trim panel - "removing" chapter

Removing adjustment fitting (seat belt height adjuster)

Removing adjustment fitting (seat belt height adjuster)

Installation Location:

Installation position for adjustment fitting (seat belt height adjuster)

Removing adjustment fitting

1. Unscrew fastening screw -1- .

2. Guide the adjustment fitting -2- upwards out of the B-pillar in -direction of

arrow-

 .

Installing adjustment fitting (seat belt height adjuster)

Installing adjustment fitting (seat belt height adjuster)

Installation Location:

Installation position for adjustment fitting (seat belt height adjuster)

Diagnostic system: reading out fault memory and activating systems

Removing adjustment fitting (seat belt height adjuster)

2847

Removing adjustment fitting

1. Run adjustment fitting -2- down into the B-pillar -direction of arrow- and tighten the fastening

screw -1- . Tightening torque → Tightening torque: 17 ftlb.

Subsequent work

Subsequent work

Install B-pillar trim panel. → 706719 Removing and installing B-pillar trim panel - "installing" chapter

997110, 997111, 997120, 997121, 997410, 997411, 997430, 997431

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

Diagnostic system: reading out fault memory and activating systems

Installing adjustment fitting (seat belt height adjuster)

2848

 

 

 

 

 

 

 

Content   ..  670  671  672  673   ..