Porshe 911 (997). Manual - part 513

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  511  512  513  514   ..

 

 

Porshe 911 (997). Manual - part 513

 

 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work

2209

- Preliminary work
- Removing hardtop fastening
- Installing hardtop fastening
- Subsequent work

Preliminary work

Preliminary work

Remove cover for the rear. → 705319 Removing and installing cover for rear- chapter on "Removing" [997310
997311 997320 997321]
→ 705319 21 Removing and installing cover for rear- chapter on
"Removing" [997610 997611 997620 997621]

Removing hardtop fastening

Removing bracket for hardtop mount

Installation Location:

2210

Installation position of bracket for hardtop mount

Removing bracket for hardtop mount

Note

Only when removing the left bracket for hardtop mount.

1. Press in locking tabs -Arrows A- and pull electric plug connection -1- up and off -Arrow B- .

2. Unscrew fastening screws -2- inside and remove the retaining angle -3- .

3. Unscrew fastening screws -2- outside and remove bracket for hardtop mount -4- upwards out of the frame

of roll-over protection system -5- .

Installing hardtop fastening

Diagnostic system: reading out fault memory and activating systems

Removing bracket for hardtop mount

2211

Installing bracket for hardtop mount

Installation Location:

Installation position of bracket for hardtop mount

Installing bracket for hardtop mount

1. Position bracket for hardtop mount -4- on frame for roll-over protection system -5- and screw down

the fastening screws -2- on the outside. Tightening torque → Tightening torque: 9.7 (7.2 ftlb.) Nm

2. Position retaining angle -3- on frame for roll-over protection system -5- and screw down with the

fastening screws -2- on the inside. Tightening torque → Tightening torque: 9.7 (7.2 ftlb.) Nm

Note

Only when removing the left bracket for hardtop mount.

3. Press in electric plug connection -1- until it audibly engages.

Diagnostic system: reading out fault memory and activating systems

Installing bracket for hardtop mount

2212

 

 

 

 

 

 

 

Content   ..  511  512  513  514   ..