Porshe 911 (997). Manual - part 227

- Preliminary work
- Removing sealing ring for halfshaft flange
- Installing sealing ring for halfshaft flange
- Subsequent work

Tools

Designation

Type

Number

Explanation

Pressure piece

special tool

9734

Preliminary work

Preliminary work

1. Raise the vehicle at the prescribed jacking points. →   Raising the vehicle

2. Remove the underbody panel. → 519419 Removing and installing rear cover - chapter on "removing"

3. Remove left halfshaft flange. → 392519 Removing and installing left halfshaft flange - "Removing"

chapter

Removing sealing ring for halfshaft flange

Removing sealing ring for halfshaft flange

1065

Levering out the sealing ring

1. Lever out the sealing ring from the transmission cover.

Installing sealing ring for halfshaft flange

Installing sealing ring for halfshaft flange

Screw in special tool

1. Screw M10 x 30 hexagon-head bolt into side B of Pressure piece 9734.

Sealing ring on special tool

2.

Diagnostic system: reading out fault memory and activating systems

Removing sealing ring for halfshaft flange

1066

Thinly coat sealing lip and outer circumference of sealing ring with Vaseline and place the sealing
ring on side A of pressure piece 9734 .

Tapping in sealing ring

3. Hammer the sealing ring along with pressure piece 9734 completely into the transmission cover by

hitting the hexagon-head bolt.

Subsequent work

Subsequent work

1. Install left halfshaft flange. → 392519 Removing and installing left halfshaft flange - "Installing"

chapter

2. Check transmission oil level. → 340101  Checking transmission oil

3. Fit the underbody panel. → 519419 Removing and installing rear cover - chapter on

"installing"

4. Lower the vehicle.

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Diagnostic system: reading out fault memory and activating systems

Installing sealing ring for halfshaft flange

1067

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Diagnostic system: reading out fault memory and activating systems

Subsequent work

1068