Porshe 911 (997). Manual - part 134

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  132  133  134  135   ..

 

 

Porshe 911 (997). Manual - part 134

 

 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Work subsequent to installing throttle body

693

- Preliminary work
- General warning notes
- Removing intake distributor, cylinder bank 1-3
- Removing intake distributor, cylinder bank 1-3
- Removing intake distributor, cylinder bank 4-6
- Installing intake distributor, cylinder bank 4-6
- Subsequent work

Tools

Designation

Type

Number

Explanation

3/8" extension, 16°
movable

commercially
available tool

NR.15

Preliminary work

Preliminary work for removing intake distributor

1. Disconnect the battery → 271000 A5  Work instructions after disconnecting the battery - chapter on

"disconnecting" .

2. Remove air cleaner housing → 242519 Removing and installing air cleaner housing - chapter on

"removing".

3. Remove tuning pipe → 247419 Removing and installing tuning pipe - chapter on "removing".

General warning notes

694

Danger from Pentosin

WARNING

Danger of injury and damage to material through Pentosin

Irritation and damage to skin

• 

Damage to hoses and wiring

• 

→ Wear protective gloves and goggles

→ If the eyes or skin come into contact with the fluid, wash immediately with water!

→ Collect escaping Pentosin

→ Use caps to protect the wiring against soiling and damage!

→ Immediately clean hoses and wiring thoroughly

Removing intake distributor, cylinder bank 1-3

Removing intake distributor, cylinder bank 1-3

WARNING

Danger of injury and damage to material through Pentosin

Irritation and damage to skin

• 

Damage to hoses and wiring

• 

→ Wear protective gloves and goggles

→ If the eyes or skin come into contact with the fluid, wash immediately with water!

→ Collect escaping Pentosin

→ Use caps to protect the wiring against soiling and damage!

→ Immediately clean hoses and wiring thoroughly

Note

For better accessibility when removing the intake distributor from cylinder bank 1-3, the three-phase
generator should be removed.

1.

Diagnostic system: reading out fault memory and activating systems

Danger from Pentosin

695

Remove three-phase generator→ 272219 Removing and installing three-phase generator - chapter
on "removing".

Left engine compartment line connections

2. Open line connections in left of engine compartment.

2.1. Loosen the vacuum lines for the brake booster -1- . For the tandem pump feed line, remove the plastic

protection, push the holder forward and pull off the line. Immediately put plastic protection back in
place.

2.2. Disconnect tank vent line -2- . In order to do this, press the lugs of the rapid-action coupling and pull off

the line (vent line remains fitted -3- ).

Cable holder

3. Remove plastic lines from cable holder over the fuel distributor pipe -1- and pull cable holder up and

off → Cable holder .

Plastic lines

4. Release lines over the fuel distributor pipe (unclip lines from the holders and secure with a tie-wrap

to the coolant expansion tank) → Plastic lines .

Diagnostic system: reading out fault memory and activating systems

Removing intake distributor, cylinder bank 1-3

696

 

 

 

 

 

 

 

Content   ..  132  133  134  135   ..