Porshe 911 (997). Manual - part 1210

 

  Index      Hummer     Porshe 911 997 series - service repair manual 2004-2008 year

 

Search            

 

 

 

 

 

 

 

 

 

Content   ..  1208  1209  1210  1211   ..

 

 

Porshe 911 (997). Manual - part 1210

 

 

- Information

Information

Axle joints: checking play and dust boots

1. Check

play.

2. Visually inspect the dust boots for

damage.

Note

When doing so, the rubber dust boots should be pressed down with the fingers to reveal hidden
cracks.

• 

If a rubber dust boot leaks, the corresponding joint or control arm must be replaced, because any dirt
or moisture that seeps in will destroy the joint.

• 

3. Inspect the dust boots of the axle joints (ball joints) on the wheel suspension (front and rear) as follows:

Place the vehicle on a lifting platform with the steering lock disengaged.

• 

Perform a visual inspection after cleaning.

• 

Note

Over a small area in the vicinity of the brake cover panels, no visual inspection is possible.

• 

Check this area by touch.

• 

The procedure for the front axle is as follows:

Turn the front wheels as far as they will go

• 

Perform a visual inspection of the visible surfaces on the left and right

• 

After turning the front wheels to the other steering stop, check the other half of each rubber dust boot.

• 

4997

Drive shafts: visual inspection of boots

–  Perform a visual inspection of the boots for leaks and

damage.

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321, 997410, 997411, 997430, 997431,
997610, 997611, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

Diagnostic system: reading out fault memory and activating systems

Drive shafts: visual inspection of boots

4998

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Drive shafts: visual inspection of boots

4999

50 IN Processing structural body adhesive - as of MY
2005

- Tools and materials
- Information on the use of structural adhesives in vehicle construction
- Processing adhesives
- Handling primer
- Handling processing devices

Tools

Designation

Type

Number

Explanation

Primer

commercially available tool

Tools and materials

Processing structural body adhesive

Tools and materials for structural bonding

Item

Designation

Source

Explanation

-A-

Primer

→ "See Parts Catalogue in Main Group 8 "

-B-

Processing gun

→ "See Parts Catalogue in Main Group 8 "

-C-

Betamate 2096 adhesive set

→ "See Parts Catalogue in Main Group 8 "

5000

 

 

 

 

 

 

 

Content   ..  1208  1209  1210  1211   ..