Porshe 911 (997). Manual - part 1076

Stick rubber sleeve together.

Note

Only for vehicles with HBA.

6. Cut through the rubber sleeve -a- and insert the HBA line -arrow A- . Stick the rubber sleeve together at

the cut edge -a- using a commercially available PUR adhesive and seal. Press the rubber seal into the
opening -arrow B- .

Crimping lines

Note

Select a place for the joint where there is enough space to join all the lines present.
Do not cut the lines too short in case they have to be laid in a different position if there is insufficient space in
the area of the joint.

Note

The greatest care must be used in the individual work steps for stripping insulation from, crimping, and
shrinking/insulating the electric lines.
The procedure for stripping insulation from, crimping, and shrinking/insulating the electric lines must be
complied with and observed. The procedures are described in detail in the repair kit for harnesses
NR.155-1

.

Crimping samples are to be prepared before beginning work.

7. Crimp lines in area around -b- .

7.1. Cut off lines in different lengths (due to the shrink-fit connections).

7.2. Slide shrink-fit hoses onto the lines.

7.3. Strip 10 mm of insulation off the wires.

Diagnostic system: reading out fault memory and activating systems

Installing rear ABS wire harness

4461

7.4. Crimp lines using crimping sleeves and the hand crimping pliers from the repair kit for harnesses

NR.155-1

.

7.5. Slide the shrink-fit hoses over the crimp connections and carefully shrink them using the hot-air blower

with special nozzle

 (recommended accessories for the repair kit for harnesses) so that they are

watertight.

7.6. Wrap commercially available PVC tape all around the area of the connection

points.

Subsequent work

Subsequent work on front ABS wire harness

1. Install plenum panel cover. → 852219 Removing and installing cover - section on "Installing"

2. Install front wheel housing liner (rear section). → 505619 Removing and installing front wheel

housing liner - section on "Installing"

3. Carry out work instruction after disconnecting the battery. → 2706IN Work instructions after

disconnecting the battery

Subsequent work on rear ABS wire harness

1. Install trim panel for seat well. → 702919 23 Removing and installing trim panel for seat well -

section on "Installing"

2. Install rear side trim panel. → 707519 Removing and installing rear side trim panel - section on

"Installing"  [997310 997311 997320 997321]→ 707519 Removing and installing rear side trim
panel - section on "Installing"  [997110 997111 997120 997121]

3. Remove rear backrest. → 724719 Removing and installing rear backrest - section on

"Installing"

4. Install wheel. → 440519 Removing and installing wheel -

installing

5. Carry out work instruction after disconnecting the battery. → 2706IN Work instructions after

disconnecting the battery

997110, 997111, 997120, 997121, 997310, 997311, 997320, 997321

WARNUNG

Diagnostic system: reading out fault memory and activating systems

 Subsequent work

4462

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

Diagnostic system: reading out fault memory and activating systems

Subsequent work on rear ABS wire harness

4463

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work on rear ABS wire harness

4464