Porshe 911 (997). Manual - part 70

Chain tensioner, cylinders 1 - 3

6. Insert chain tensioner for cylinder 1 - 3 with new sealing ring (hexagon a/f 32) and tighten to the

specified torque. → Tightening torque: 80 (59 ftlb.) Nm

7. Secure coolant pipe on cylinder side 4 - 6 with two M6 x 12 hexagon-head bolts. → Tightening torque:

10 (7.5 ftlb.) Nm

8. Fit new closure caps on cylinder head cover.

9. Pull locating pin out of the crankshaft vibration

balancer.

Subsequent work for bearing cover for intermediate shaft

Subsequent work for bearing cover for intermediate shaft

Tiptronic transmission:

1. Install drive plate for converter → 136319 Removing and installing drive plate for converter -

section on "Installing".

2. Refit Tiptronic transmission → 373527 Removing and refitting automatic transmission - section on

"Refitting" [997120 997121 997320 997321]→ 373527 AG Removing and refitting automatic transmission
- section on "Refitting" [997430 997431 997620 997621].

3. Install engine → 101019 23 Removing and installing engine - section on "Installing".

Manual transmission:

4. Install double-mass flywheel → 136019 Removing and installing double-mass flywheel - section on

"Installing".

5. Install clutch → 305019 Removing and installing clutch - section on

"Installing".

6. Install transmission → 343519 Removing and installing transmission - section on

"Installing" [997430 997431 997620 997621]→ 343519 Removing and installing transmission -
section on "Installing" [997120 997121 997320 997321].

7. Filling in engine oil → 170155 Engine oil and oil filter change - section on "Filling in".

8. Install air cleaner housing → 242519 Removing and installing air cleaner housing - section on

"Installing".

Note

Diagnostic system: reading out fault memory and activating systems

 Subsequent work for bearing cover for intermediate shaft

437

Note the work instructions for disconnecting and reconnecting the battery.

• 

9. Connect the battery → 271000  Work instructions after disconnecting the battery.

997120, 997121, 997320, 997321, 997430, 997431, 997620, 997621

WARNUNG

Gefahr des Verlusts der Text-Bild-Zuordnung beim Ausdruck.

Aus technischen Gründen kann derzeit nicht ausgeschlossen werden, dass trotz
einwandfreier Darstellung auf dem Bildschirm beim Ausdruck der
Zusammenhang von Text und zugehörigem Bild verloren geht.

• 

Wird der Fehler nicht bemerkt, besteht die Gefahr, daß Arbeiten nicht korrekt
durchgeführt werden und es dadurch zu Personen- und Sachschäden kommt.

• 

→ Vergleichen Sie deshalb nach dem Druckvorgang unbedingt die Ausdrucke mit der
Bildschirmdarstellung. Korrigieren Sie die Ausdrucke im Fehlerfall so, daß der Inhalt der
Bildschirmdarstellung zutreffend wiedergegeben wird.

WARNING

Danger of losing text-figure correspondence when printing out.

For technical reasons, it can currently not be ruled out that the correspondence
between text and associated figure can be lost when it is printed out, even though
the display on the screen is correct.

• 

If the fault is not noticed, there is the danger that work will not be performed
correctly which can cause injury and damage.

• 

→ Therefore, always compare printouts with the screen display after printing them out. Correct
the printouts if they are faulty so that the content of the screen display matches that on the
printouts.

AVERTISSEMENT

Risque de perte de la correspondance texte-illustration lors de l'impression papier.

Pour des raisons techniques, il ne peut pas être exclu à l'heure actuelle que, même
en cas d'affichage correct à l'écran, la correspondance entre le texte et l'illustration
puisse être erronée sur l'impression papier.

• 

Si l'erreur passe inaperçue, on court le risque d'exécuter certaines opérations de
manière incorrecte pouvant conduire à des dommages corporels et matériels.

• 

Diagnostic system: reading out fault memory and activating systems

Subsequent work for bearing cover for intermediate shaft

438

→ Comparez impérativement pour cette raison les impressions papier avec l'affichage à l'écran.
Corrigez-les en cas d'erreur de manière à reproduire correctement l'affichage à l'écran.

ATTENZIONE

Pericolo di perdita dell'abbinamento testo-immagine nella stampa.

Per motivi tecnici non è escluso che, nonostante la rappresentazione sullo schermo
risulti perfetta, durante la stampa venga persa la corrispondenza fra testo e
relativa immagine.

• 

Se tale difetto non viene rilevato vi è il pericolo che i lavori non siano eseguiti
correttamente; ciò può avere come conseguenza lesioni e danneggiamenti.

• 

→ Per questo motivo, dopo la stampa è assolutamente necessario confrontare le stampe con la
rappresentazione sullo schermo. In caso di errore si prega di correggere le stampe, così da
garantire la riproduzione esatta della rappresentazione sullo schermo.

ADVERTENCIA

Al imprimir se corre el riesgo de perder la correcta asignación de las figuras al texto.

Por motivos técnicos, por el momento no se puede descartar que, aun siendo
correcta la imagen que aparezca en la pantalla, al imprimir se pierda la
correlación entre el texto y la figura correspondiente.

• 

Si este error pasara desapercibido, existe el riesgo de que los trabajos no se
ejecuten de forma correcta y, por tanto, se produzcan daños personales y
materiales.

• 

→ Por ello le rogamos que tras el proceso de impresión compare siempre las copias impresas con
la imagen de la pantalla. En caso de error, corrija las copias impresas de forma que se
correspondan con el contenido de la imagen de la pantalla.

Diagnostic system: reading out fault memory and activating systems

Subsequent work for bearing cover for intermediate shaft

439

- Removing bearing cover for intermediate shaft
- Installing bearing cover for intermediate shaft

Tools

Designation

Type

Number Explanation

socket wrench

special tool

9110

locating pins

special tool

9595/1

puller

special tool

9673

adjusting gauge

special tool

9686